sane-dc210(5) SANE Scanner Access Now Easy sane-dc210(5)
NAME
sane-dc210 - SANE backend for Kodak DC210 Digital Camera
DESCRIPTION
The sane-dc210 library implements a SANE (Scanner Access Now Easy)
backend that provides access to the Kodak DC210 camera. THIS IS EXTREMELY
ALPHA CODE! USE AT YOUR OWN RISK!!
DEVICE NAMES
The current version of the backend only allows one camera to be
connected. The device name is always "0".
CONFIGURATION
The contents of the dc210.conf specify the serial port and baud rate to
use. The baud rate specifies the maximum rate to use while downloading
pictures. (The camera is always initialized using 9600 baud, then
switches to the higher rate). On my 90MHz Pentium, I usually have no
problems downloading at 115200 baud as long as the system is not
excessively busy and the "interrupt-unmask flag" is set in the IDE driver
(hdparm -u1). Supported baud rates are: 9600, 19200, 38400, 57600, and
115200.
The dumpinquiry line causes some information about the camera to be
printed.
cmdrespause specifies how many usec (1,000,000ths of a second) to wait
between writing the command and reading the result. 125000 seems to be
the lowest I could go reliably.
breakpause specifies how many usec (1,000,000ths of a second) between
sending the "back to default" break and sending commands.
Empty lines and lines starting with a hash mark (#) are ignored. A
sample configuration file is shown below:
port=/dev/ttyS0
# this is a comment
baud=115200
dumpinquiry
cmdrespause=125000
breakpause=1000000
FILES
/opt/local/etc/sane.d/dc210.conf
The backend configuration file (see also description of
SANE_CONFIG_DIR below).
/opt/local/lib/sane/libsane-dc210.a
The static library implementing this backend.
/opt/local/lib/sane/libsane-dc210.so
The shared library implementing this backend (present on systems
that support dynamic loading).
ENVIRONMENT
SANE_CONFIG_DIR
This environment variable specifies the list of directories that
may contain the configuration file. On *NIX systems, the
directories are separated by a colon (`:'), under OS/2, they are
separated by a semi-colon (`;'). If this variable is not set, the
configuration file is searched in two default directories: first,
the current working directory (".") and then in
/opt/local/etc/sane.d. If the value of the environment variable
ends with the directory separator character, then the default
directories are searched after the explicitly specified
directories. For example, setting SANE_CONFIG_DIR to
"/tmp/config:" would result in directories tmp/config, ., and
/opt/local/etc/sane.d being searched (in this order).
SANE_DEBUG_DC210
If the library was compiled with debugging support enabled, this
environment variable controls the debug level for this backend. A
value of 128 requests maximally copious debug output; smaller
levels reduce verbosity.
SEE ALSO
sane(7)
AUTHOR
Brian J. Murrell
This backend is based somewhat on the dc25 backend included in this
package by Peter Fales.
The manpage was copied from the dc25 backend and somewhat edited by
Henning Meier-Geinitz.
BUGS
Known bugs/limitations are: ?
More general comments, suggestions, and inquiries about frontends or SANE
should go to the SANE Developers mailing list (see
http://www.sane-project.org/mailing-lists.html for details). You must be
subscribed to the list, otherwise your mail won't be sent to the
subscribers.
11 Jul 2008 sane-dc210(5)
sane-backends 1.2.1 - Generated Sat Feb 25 11:43:48 CST 2023